Did you record a video of your mod?
This is a very in depth mod using the method he did above; it will work but its tough. I did one at EVO2016 and it took me a hot minute as well as a lot of cutting, crimping, etc. If you can wait just a few more weeks I will have TES+ EZ MODs that eliminate all of this.
Currently de-rushing. This will be a TES+ and a TE2+ conversion to hitbox. Pics of final products are the ācheck out my new arcade stickā thread. But as Jasen said you shoud wait for the TES+ EZ Mod.
Edit: Mevermind. The problem was with ufb firmware. It seems it didnāt update properly the first time even though the launcher said that it did.
This sounds like a UFB issue, not an EZ MOD issue. If the PC is showing everything working that tells me that all of the signals are being passed to the UFB properly and its interpreting the signals properly. I would suggest updating the consoles to ensure they are at the most current FW.
The Jumpers and LED functions do not affect the UFB in anyways, they just route signals around.
I tried reflashing the UFB again and it seems to be working now. Fingers crossed while I do more testing. Super bizarre because I literally just flashed it an hour earlier. Super strange.
Either way, thanks for making the EZ Mod such a easy and intuitive install 
I have a Remora, FGWiget, Uilas LEDs, and Arceyes 3 from some older sticks that Iād like to try to use for the TE2+. But which one!?
Update, I tried using the Remora but had issues with using both the TE and TE S C1 and C2 JST connectors to the Brooks UFB. Couldnāt get 1K and 2K to function using TE JST pin connectors.
I ordered some 6 pin JST 2.0 mm to try the TE S connectors, didnāt know where to wire Kill ground except to a ground point on the UFB, but that had some more issues. None of the buttons worked and 2 directions work, but the wrong way. I kinda freaked thinking I bricked the EZ Mod and UFB, although the LEDs in them were working. I unhooked everything and pulled the Remora outta there. Hooked up the EZ Mod and UFB, plugged it in and everything worked fine. Im sure its something with the kill ground not wired properly but I moved on.
The FGWiget works! I added a balltop LED and some 24mm Peles for Start and Select. Again, great product Jasen!
hi everyone
i feel bad , my stick make the same with my original pcb TE2+ 
(i have EZ TE2+ with UFB brook)
after playing like 30min / 1 hours, my directions of my stick are locked my character , jump infinite or infinite gard why?
i disconnected the cable of sanwa JLF when is happen, and still jump infinite
i trying another one cable usb, i updated my UFB brook
someone can help me please?
Please can someone help me? iām seriously disapointed by EZmod TE2+ same shit like TE2+ original pcb
again today , my stick In the middle of the match, sometime is like disconected ,nothing works , all butons, stick directionā¦
and sometime, the direction of stick infinite āleftā or ājump leftā infinite WHY?? and when it happen i need to unplug usb 2 or 3 times for is work normally
Iām not sure; I have the same setup but I do not have the J7 and J2 pins connected based on your picture. I only use it for PS4 and PS3.
@POPSKNZ i use too only on PS4 , i will try to play without J2 & J7
that so weird ,what happening with my stick
Are all of the firmwareās up to date on console and the UFB?
Have you retried re-flashing the UFB again?
What happens when you use it on an XBOX ONE? What happens when you use it on the PC?
How long does it take until it stops working?
Remember, the EZ MOD is just a complex wiring harness with some processing to use the LEDs and indications on the TE2ā¦ the Brook UFB is still 100% the brains of the setup. Comments such as : āiām seriously disapointed by EZmod TE2+ same shit like TE2+ original pcb :(ā isnāt going to get a whirlwind of people ready to help diagnose your problem especially when there isnāt enough information in your post to help pin-point the issue. Please answer the questions above and do some testing on the PC for at least 30 minutes. If you have no games on the PC you can always run JOY.CPL and use the properties of the joystick to test inputs.
@āJasen Hicksā thanks so much for answer
my ps4 have the last firmware, and i installed 2 times firmware in brook ufb
it stop between 40 min / 1 hour and more , and it happen all the time on match, never happen on menu
i dont have Xbox one, i will test on computer tomorrow
sorry for my bad comment, im lil bit frustrating by this problem for a second time
@"Jasen Hicks"
i updated again firmware before to play
and i played today on my PC, after after a moment, same like ps4 nothing work ,
no direction no button , need to unplug & plug stick for he work again
First time:
https://youtu.be/Q3NXGJS4QmE.
Second time :
https://youtu.be/04L-lxqIKzk
here pics with joy.cpl
https://img11.hostingpics.net/thumbs/mini_990464StickTE2.jpg
https://img11.hostingpics.net/thumbs/mini_932026stick2.jpg
Either something is not connected right or the Universal Fighting Board has a fault. Whomever you bought the UFB from you should contact and arrange a replacement if you are within their replacement policy timeline.
@āJasen Hicksā so u tell me āsomething not connnected rightā i disconnected J2 & J7 same like @POPSKNZ and my stick workin fine! no problem
so u have any idea why my problem come when i plug J2 & J7?
Brook changed the function of J7 to be a SOCD mode change instead of a touchpad, so i suspect the signals from the Touch Pad are causing some weird thing to happen in the processor of the UFB since its not getting the expected signals for a mode shift and instead getting unrecognized signals from the TouchPad. The J7 shouldnāt have any effect since its the DP/LS/RS mode selector. Iām willing to bet that connecting J7 will be fine.
They changed this a few months ago, about a year after the EZ MOD was designed.