At a guess, you have the ‘5’ ribbon and the ‘6’ ribbon going to the wrong spots on the distrobution board. Take the ribbons going to CN1 and CN2 on the distrobution board, swap them, and test again please.
Gig 'em.
Guessed correct! That fixed the problem, thank you so much!
Just ordered a TE Kitty board this morning, I can’t wait for it to get here. I can’t thank you enough for these awesome boards…and I don’t even have it yet. 
Stay tuned for more worship.
Kei
Installed a TE Kitty with a TE-S Kit yesterday in my Chun-Li sitck with no problems at all. It was pretty easy to install. It’s only been a day… but I would highly recommend.
So I got a question about the Kitty RJ-45 Jack. If I install this option jack, will I still have to use the built in USB cable for PC/PS3/360? I ask because I think the cable is far too long and harder to deal with. I would rather just install the RJ-45 Jack and use that instead.
You can use use either, or both. Your choice. The PS3 code runs pretty fast, so make sure to use a good quality USB cable when you make your RJ45->USB cord.
just did the soldering fix to my vlx kitty pcb thx alot now my vlx is 100% awesome again thx alot
Just to clarify “disabled the stick”, you are referring to the “X/Y Axis” and “X/Y Rotation” in the Game Controller app not recognizing input regardless of LS/DP/RS switch position, correct?
Once the Kitty is forced into 360 mode, does it remain completely passive (i.e. will not listen for or send out any signals) until the stick is unplugged and reconnected?
I have the mlg fight stick. Hear it has same Pcb as CHUN LI TE-s stick. Do I need a TE-s harness on top of a kitty for dual mod?
It’ll act the same as it did before the Kitty was installed.
Does the ‘lock’ slider disable start and back? If so, you need the TE-S harness as well.
Do I check this before or after the kitty is installed?
Before. It’s the generic ‘do I need to get the TE-S harness with my Kitty kit?’ question.
I have a 360 MLG stick, do I need to test if the ‘lock’ slider disable start and back on a 360, or can I test it on a PC, or either?
Either.
Hey ^^
I just installed my kitty on my TE-S stick but somethings wrong.
When im in the kitty mode, all the buttons light up when i click them as expected to do but my RB dont.
And when im in the normal xbox360 mode, then the RB button does not light up brighter when i use turbo like the others but blink until i activate turbo on that button ofc.
Yet all the buttons respond when i try them in both modes in Game Controllers applet. I dont have my PC with ssf or PS3 atm so i cant try it in the game.
Thx for the help ^^
you may have the connectors for the button distros swapped
Which button connectors do you mean? The ones from TE-S harness?
Sounds like a diode popped off during the installation. Check the bottom of the board, you should see 9 diodes labelled D1-D9. I expect your missing one of those. Check the bag the TE Kitty came in and the inside of your case. Its TEENY tiny and black.
Nah. All of the buttons respond properly in the game controller’s applet. The only problem was that the LEDs for RB light up during turbo in 360 mode, but dont light up from a button press. So the fault is almost certainly in the section of (game signal)----(resistor)—(diode)----(LED panel signal for the RB), the part that makes the LEDs light up on press.
At the bottom of what board? the LED daughterboar?
No, bottom of the Kitty board.