Correct. Straightforward soldering job to the contacts.
2 Likes
A multimeter helps with finding all the commons
1 Like
thanks man. I got the diagram floating on the internet already. Just need to make sure that I dont need extra stuffs to get it right.
1 Like
thank you too man <3
1 Like
Any shop out there on the internet make plexiglass tops for the Dreamcast Green Goblin anymore? Tek-Innovations is long gone, but I guess thereās no demand for this stick as time has gone on. The top plate on my Green Goblin has rusted a bit, and Iām afraid if I look at it funny the thing will turn into dust.
Iām trying to leech what I can from web.archive, but it doesnāt look like they got much from Tek-Innovations past the front of the Agetec section.
Greetings,
Can anyone point me towards a video or thread for installing a Brooks UFB and Mc Cthulhu inside of the same case? I bought these for a project years ago that Iām just getting around to. I know Brookās has a retro board out now that would be simple to drop in but I want to undertake the project now that I have time. I do not have an IMP and donāt know of any place that has them in stock. I found a thread but all of the pictures are dead links now.
My goal is to have both boards powered on at the same time and sharing a common output (RJ45). If anyone is running this set-up and could take a picture of how their wired it or walk me through the process Iād be grateful. I canāt find much on google as since the brookās retro board is out most results point me to pages about that. I found a thread detailing this on the forums years ago but I canāt seem to find it now. I found a similar thread but as I said most of the images point to dead links so it isnāt very helpful.
Anyone have a good site to buy madcatz TE metal replacement panels? Iām looking to get one with a Korean size joystick hole (35mm).
Focus attack mentioned something to this on their Instagram. Perhaps they are gauging interest, so the best bet is to email them and ask.
I actually emailed them directly after I posted this. They had a canned āif itās not in our store, we donāt provide it yet.ā I just posted on their IG to increase interest. Thanks!
those of you who use El Gato capture systems,
How do you capture systems that have the option for component input?
Hi everyone,
I made a thread about this the other day before seeing this one, so apologies for the repetition, but I was wondering if anyone knows if itās possible to buy the silver side panels for the Qanba Obsidian anywhere. I bought one recently and it turned up with a small chip to the left (stick side) panel which Iām keen to sort out, because it was originally in mint condition. I know some people remove these panels when they mod theirs, but I havenāt seen any on auction sites, etc.
Thanks!
personally, Iād try firing off a social media message to Qanba about it. Otherwise youāll probably be looking at scouring eBay for broken Obsidians.
2 Likes
Thanks for your reply! I emailed them through the website but didnāt think to try FB/Twitter, etc. Hopefully Iāll get a message about it soon. 
Random question but I am looking to make my own USB B cables for my sticks and I canāt for the life of me find any DIY sets of these with the shell part. All I can stumbling on are USB mini B. Any recommendations on where to find these?
digikey and mouser
I just donāt have a part number for you
Sorry for another question about the Obsidian, but whatās the best way to mount an LS-62 to this? I tried removing the SE-P-40 mounting plate to make it flush with the top panel, but it isnāt wide enough to match up with the screw holes, and with the mounting plate attached the shaft (though shorter than most anyway) is half buried. An SS plate wouldnāt fit, eitherā¦
Thanks!
With many seimitsu plates you got to rotate the plate 90 degrees and use the one center hole on each side. Which also means only using 2 screws to hold it into place.
You can also try a universal mount plate.
1 Like
Ah, nice one, thanks for that! Iāll look into the universal mounts. I have a feeling the buttons might be too close to the stick for rotation to work, but Iāll definitely open it up again and try.
Is it possible to install a brook universal into a hori rap 4?
Yes, it is