Go to his order form and check to make sure, it’s very likely to be the same as the 3 others (other then being a slim case compared to original), just it’s complete white instead of a mix color.
I still love the look of exotic wood though.
Thanks 
White lacquer poplar case $100 + shipping
edit* nm
Here’s a few more “sexy Pics” to keep your mouth watering.
DeepThoughts - Piano Black Slim
Mekkanic - Piano Black Universal
Valkyrie23 - Black Dyed Maple Slim
Yuro
I ran out of clearcoat 
Don’t worry I’m running to go get some more today as well as more packing supplies.
Cases 4 Sale
Zebra (twisted tight grain) Slim No button hole pattern yet 3x24mm + 1 NAUSB pre drilled $150.00
Purple Striped Poplar 8xUniversal 4x24mm + NAUSB pre drilled $75**
Black Dyed Maple Universal 3" 8xUniversal 4x24mm + 1 NAUSB pre drilled $95**
Poplar stained Reg Mahogany Universal 3" Blank button layout 4x24mm + 1 NAUSB pre drilled $100.00
** = (2nd’s) price is reduced because it has a small defect, I can supply pics on request
Looking good, Voltech - I can’t wait!
any chance of seeing rounded ones volt? even though i love
the TE shape i preefer rounded ones
Damn i cant wait for my slim case now, friggin cases look amazing!!!
trying to understand the top panel, screws/no screws issue… is this to fasten the plexi? for example, if I get the no screw, then you screw in the top panel, and then the plexi is held on by screw in buttons, and if I get the screw in, the plexi screws to the top panel so I can use snap ins?
and also, I can’t see all three button layouts… is the TE button spacing a bit further away from the joystick? on the HRAP3 they are too close to the stick and I’d like a setup like the TE, but want to make sure it’s a bit further from the stick than an HRAP…
cool deal
Yes you got it. No screw holes means that the plexi will be held down only by the screw in buttons. The MDF below is still screwed down either way. If you plan to use all snap in buttons you would want to choose the “screwed down” option. If you plan to use at least 4 or more screw in buttons than the no screw holes option would be fine. By default I will make the cases with the “no screw holes” option unless otherwise requested.
All three layouts have the same spacing between the stick and the buttons. My layout is just a little further apart than the TE because of my universal mounting plate. (about 75mm from the center of the stick to the center of the first button) Hope that answers your questions.
On another note I have packed and prepared the following sticks for shipping
Reyals - Ready to ship
Valkyrie23 - Ready to ship
LLama_egg - Ready to ship
Saitou - Ready to ship
DeepThoughts - Ready to ship
mekkanic - Ready to ship
The following cases may not ship until next week.
PJM33 - Your case is ready but we still need to work out the shipping details.
Yoro - First layer of clear coat applied to your Zebra case but I still need to sand, re-coat and let it cure overnight.
WupWuh1134 - Your blank poplar frame is cut but it needs some sanding. Button layout and plexi have not been cut yet
Vince34 - Your blank maple case has been cut and will also need some sanding. Button layout and plexi have not been cut yet.
Whew, did I miss anyone?
possible to move it to 80-85mm? If not it won’t be a huge issue… let me know…
and If I understand correctly, a standard universal stick out of poplar will run me $65… correct?
can you dye (colored stain) as well?
Thanks for the help… hope to place an order in the next couple of weeks… the cases are beautiful!!!
Also, noticed you have options for plexi bottom and rubber feet… what do these cost… and also, how do you deal with a usb hole for a standard cord (not the NAUSB)?
No I use a template to cut out the stick location and that would be too difficult to move around. I have large hands and it feels really good trust me 
Yes sir and a blank poplar slim would cost the same
Not sure what you mean but you would either dye or stain not usually both. If you want help staining or dying I can try and help you out.
Thanks
No extra cost for these just some people wanted wooden bottoms instead of plexi. As far as the hole for a usb cable you can just say in the Special requests “no NAUSB hole” and I will just cut a notch in the plexi, or if you want it in the wood or a small hole drilled I can do that too. I like what Stephen is doing with the brass beauty ring and may even try that if I can get some.
Thanks for the updates!
thanks for the time to answer my questions…
Now is a great time for arcade stick building… so many talented case builders!
steve’s cases are beautiful, but are a bit too small for my tastes, and out of my price range… :wasted:
I’ll gladly pay for my case this time, but next time I’ll do it myself…
I’ll order one up when funds are in hand… 
The following cases shipped
Reyals - shipped
Valkyrie23 - shipped
LLama_egg - shipped
Saitou - shipped
DeepThoughts - shipped
mekkanic - shipped
I have sent you an e-mail. Also all the cases look amazing
Would something be able to be setup for local pick up? I’m really liking these sticks.
Yeah for sure, saves me the hassle of shipping.
Yo voltech is there any chance u doing 2 player stick on the slim line case. let me know.
I’ve been thinking about it but need to get some free time to experiment a little. Plus I’ll need to pick up some larger pieces of plexi. I’ll keep you posted if I do