Pc problem with 6 button arcade stick

Classic Fighting Games Street Fighter x Tekken
1

I’m trying to set the controls and no matter what I do I can’t get it to save and work properly, I tried a few tutorials like downloading the 360ce.ini and stuff and setting my controls there but still doesn’t seem to work and save properly too.

Using a ps3/pc cthulhu.

2

i use a 15 years old “ccl usb smart joy deluxe” with a 15 years old “the pad by innovation” (10 Buttons, 1 axe) on it. To make the game save the configurations its required to get all important buttons configured once, or the game wont save.

in my case i connected the normal playstation 1 dual shock controller (16 Buttons, 4 axes) into the “ccl usb smart joy deluxe” to configure and make the game save it, then i unplugged the dualshock and plugged my “the pad by innovation” (10 Buttons, 1 axe) on it to test if the configuration is ok. there is one important button in the game you will always have to configure, its the start/next button, i set it to the “SELECT” button of my gamepad, the start button is set to light kick here hahahaaa…

3

Lol… don’t know why sfiv was simple and this they made it stupid with the config, I seem to have all the right buttons setup but it’s in the wrong order so when I change it other ‘needed’ buttons get removed and no way to change it because I don’t have 8. Well I’ll figure this out sooner or later lol

4

It know thats completely stupid, something they already knew hot to do it perfect, now they did it worse than before. If you have a 8 Button gamepad, you can only use 7 Buttons of it, because one button is always used for “start”.

  • after entering the game, if you press start with your gamepad, you can only use gamepad in the next menues and afterwards.
  • after entering the game, if you press start with your keyboard, you can only use keyboard in the next menues and afterwards.
    ==> you cannot combine the usage of your keyboard with you gamepad, it means you cannot use the “ENTER” button of your keyboard as “start”-button as one could do it with SFIV (or SSFIV_AE_v2012).
    if it helps you out, maybe you can configure your config.ini manually to configure your gamepad buttons, i post you mine as an example, maybe it can help you (and others also):
    You will find the file on win7x64 under:
    c:\users%username%\Documents\CAPCOM\SFTK\

####config.ini####
[DISPLAY]
Aspect=AUTO
FrameRate=FIXED
FullScreen=OFF
RefreshRate=60Hz
Resolution=1280x720
VSync=ON
[GRAPHICS]
BgDetail=LOW
CharacterShadows=OFF
MSAA=NONE
MotionBlur=OFF
[PAD0]
BUTTON_1=A
BUTTON_10=RS
BUTTON_11=LT
BUTTON_12=RT
BUTTON_13=
BUTTON_14=
BUTTON_15=
BUTTON_16=
BUTTON_2=B
BUTTON_3=X
BUTTON_4=Y
BUTTON_5=LB
BUTTON_6=RB
BUTTON_7=BACK
BUTTON_8=START
BUTTON_9=LS
DPAD_DOWN=DOWN
DPAD_LEFT=LEFT
DPAD_RIGHT=RIGHT
DPAD_UP=UP
UID=00030810-0000-0000-0000-504944564944
[PAD1]
BUTTON_1=A
BUTTON_10=RS
BUTTON_11=LT
BUTTON_12=RT
BUTTON_13=
BUTTON_14=
BUTTON_15=
BUTTON_16=
BUTTON_2=B
BUTTON_3=X
BUTTON_4=Y
BUTTON_5=LB
BUTTON_6=RB
BUTTON_7=BACK
BUTTON_8=START
BUTTON_9=LS
DPAD_DOWN=DOWN
DPAD_LEFT=LEFT
DPAD_RIGHT=RIGHT
DPAD_UP=UP
UID=06676666-0000-0000-0000-504944564944
[SYSTEM]
RenderingThread=ON
[GAME]
FPS=ON
[PAD2]
BUTTON_1=A
BUTTON_10=RS
BUTTON_11=LT
BUTTON_12=RT
BUTTON_13=
BUTTON_14=
BUTTON_15=
BUTTON_16=
BUTTON_2=B
BUTTON_3=X
BUTTON_4=Y
BUTTON_5=LB
BUTTON_6=RB
BUTTON_7=BACK
BUTTON_8=START
BUTTON_9=LS
DPAD_DOWN=DOWN
DPAD_LEFT=LEFT
DPAD_RIGHT=RIGHT
DPAD_UP=UP
UID=XInput Device
####config.ini####

I had connected

  • one “ccl usb smart joy deluxe”
  • one EAXUS PS3-2-USB Converter
  • DATEL WILDFIRE WIRED CONTROLLER V2 (PAD2 as its UID=XInput Device)
    so thats why 3 gamepads are listed in my config.ini

good luck

5

Thanks for the info, I’ll try and figure it out. :slight_smile: