To get a thicker supportive clear top without ribs and a good fill, the mold pressure is higher, which exacerbates flash. Normally we catch this and fix it though 
A few more things Iām looking for, an SOCD cleaner for use with the wireless 360 controller, and some sort of terminal strip I can use for the wires from the controller circuit board. If you donāt sell those, could you at least recommend where I can get them? And you mentioned that you have silenced 24mm sanwa buttons. Are those OBSC buttons? I havenāt found them anywhere on your site.
Any ETA on when the new site will be ready, or when the current issues will be resolved?
The filing is working great 5 down 3 to go. Also to Evolution I didnāt think they have silent 24mm in stock. But they do have push button pads in 24mm. I can tell you the 30mm ones work flawless as should the 24mm.
Why would you need an SOCD cleaner on a PS360+? The PCB itself already has that ability so there is no need for one. FA also carries PS360+ or even one of the custom stick builders sell them on his site here: http://www.foehammershop.com/
derp not the PS360+, I had my terminology wrong. The wireless 360 controller circuit board is what I meant.
Thanks, Iāll look at those then.
The site was moved to a new server, and we we assured issues would be resolved by tonight. We currently do not have screw blocks listed, but I believe we have a dozen or so in stock. You can also use buy the 360 with a Voltech harnesses for easy clean wiring.
Silent pads are available separately, I am on my phone, but can post a link later.
I know evolution has been shopping around but I think the reason he is settling here is the availability of some of our custom items, neither Foehammer or FA have silencers for 24mm buttons. Both shops do have the 360 though.
I have been shopping around, but I think you have nearly everything I need. I still need to find an SOCD cleaner, and Iām also in need of a Neutrik Reversible NAUSB-W-B plug, but I might be able to find one of those locally, or at least get one ebay if you donāt carry them
Are the screw blocks the long strip kind, and how many terminals do they have?
Hi. Do you have an ETA of the restock of the 0.5/1.0mm aluminum oversized JLF actuators? Iām thinking whether or not I should place my order now or wait a bit longer for those. Also, would a 2.0mm actuator be too large for the OMRON silent switch? And what kind of lbf springs would you recommend to go with the silent switch? Personally Iām not too satisfied with the silent switch/stocked spring/0.5mm actuator setup. And Iām extremely happy with default JLF/0.5mm oversized setup that Iām tempted to try out the 1.0mm. Thx.
@ixus I use a 0.5mm oversized actuator in my normal stick, and a 1.0mm oversized one with my silenced (Omron) one - and they feel very similar (both sticks have octogates). Both with 2lb springs.
We should have the aluminum actuators in September, but we have the Delrin equivalents now
I agree with Graymilkin on his set up, I would, however, go with a 1.5 lb on the native JLF.
Evolution, I sorry for the delay, I will have Susan pull them.
We are getting closerā¦ all the products are migrated, now all that is left is a bit of tweaking and point the domain to the new server.
Bryan,
You mentioned the possibility of a cheaper wiring harness in a separate thread, is that still something you and Susan are looking to add? Also, I was looking through your site for a set of replacement microswitches for an LS-56, but I was only able to find a set for the LS-32. Do you stock a switch for the LS-56?
@Kozimor I would suggest Cherryās for the LS-56 if you are looking to replace stock switches.
We are going to add a new wiring harness, Itās just a matter of settling up existing projectsā¦ The biggest of which is the new website! I would expect the new harnesses by Mid Sept. The same company is doing all the LED board harnesses which we expect any day now!
while on the subject on the LS-56, does it come standard with a square gate or octagonal?
Standard is a square gate, but this weekend we will be running a special on our new round and short throw square gates!
The special goes like this, free gate with every joystick or order over $50
Hmmmm, whatās this?
YEEEESSSSSSSS
How much lolā¦ I love how you have the FTDI already on the board. Pretty slick look. How many LED can you put on this board man ha ha ha. I feel like a kid in the candy store. Just let me know when they are for sale.
I need it.
ha ha haā¦ good one, with all the slots on the board I can see that amount. But seriously you do have a lot of spots on the board that we may just be able to do a 3D LED model like one of the post earlier stated. Man this is going the be one sick PCB with some serious options. Cant wait for you to stock them. Now get to work on a video of the board in action.
Congrats man. I know this was a long time coming project and I hope it pays off for you.
Is the website good to go? Iāll probably order everything I need this weekend, just waiting for all the issues to get sorted out.
Do you have any info on those screw blocks yet?