Couple issues with a paewang install

Tech Talk
1

Hey first post here, just installed my new paewang, but have several problems I’d like to see if anyone has any ideas about

First, my RT button when pressed detects as Z Axis in windows control panel, every other button and the joystick are working correctly, I’m not really seeing any issue with connections, but I obviously have an issue here

Secondly my home and turbo buttons are not being detected at all in the control panel, I used the turbo, xguild, ground and power from the SFxT pcb to the paewang (in pics) I presume these should be detected as a regular button in control panel?

SFxT PCB:

Paewang itself:

The bad solder job will be cleaned up once I get everything working :slight_smile:

Any help would be much appreciated

2

I think you are new to Xbox 360 Controllers.

LT is Maximum Z-Axis.
RT is Minimum Z-Axis.
Turbo is not supposed to show up in PC.
Guide is not supposed to show up in PC.

3

Yeah, haven’t really modded anything for xbox yet

Does the power light show up when plugged in on PC or no?

Thanks for the help, I’ll try it out when I get home on the consoles

4

No light is supposed to be lit if you have a Paewang.
The Paewang PCB does not have any LED indicators.

5

I’m trying to install a paewang also and am having trouble with the home button. I am 95% done but can’t figure out which wires on my hori hrap-ex ribbon cable are ground and signal. Does anyone have experience with this?

6

http://www.newthinks.info/avatar3.jpg

thank s a lot

7

Thanks for the heads up

One more time to pick your brain, Xbox and PC work flawlessly, but I get an unknown usb device while plugging into PS3, I’ve tried holding down turbo / select, would this be a ground issue?

8

PCB probably does not work.
Some Paewang PCB are bad.

Which mode you test on PC?

9

I get no change on the PC whether I hold turbo while plugging in, It always says XBOX 360 Controller for Windows

10

Oh, then you got one of the bad ones that will not switch modes.
Or maybe you did not hook up the Turbo correctly?
Are you able to Turbo Input on PC of Xbox 360?

11

That’s a negative

12

Then you did not wire up Turbo.

13

I’ll have to check it out tomorrow, again thanks for helping me troubleshoot

I have a feeling it might be the SFxT turbo/home pcb, setting up back button with turbo a good alternative to using this board?

14

Since the FightStick PRO PCB has enough buttons for Turbo and Guide and Back and Start.
Why you do not just just wire those four functions on Paewang to the SFxT PCB?
Why do the bridge with Turbo and Select on Paewang?

15

The PCB for joystick/buttons had stopped working out of no where for me, I ended up gutting it to replace everything with a paewang or something similar and ended up losing the stock cables, so I just wired vcc, ground, turbo and home… long story short, I derped

Home button is working fine so I presume that pcb is okay

16

The guide button works on my pc in 360 mode, but then again I have got the “xbox 360 controller” driver installed.

17

Yes, the Guide work on PC.
But with the MS Xbox 360 Controller Driver.
It pops up the little window to show status and for GFWL.

When in the Game Controller Applet, Guide doesn’t have an assigned PC button.

18

Amigos I have a broken Xbox360 TE, I already order the paewang PCB and the wiring harness I have a question about the Turbo and Home button, I think I can use the stock PCB so that I can use both the home and turbo buttons but how is exactly that you need to wire this? I saw on a video that you need to apply a +5v and ground to the circuit from which part of the PCB should I take the +5 V ??? Any help will be appreciated.

*I own a PS3 so I need the home button to play KOF XIII.