Street Fighter X Tekken 360 Fightpad S.D. PCB

gahrling · May 10, 2012, 8:43pm

Do you still have plans to make a new version of the DS:SMD?

IIRC you were pondering about it a while back.

Gummo · May 10, 2012, 8:48pm

none what-so-ever.

Donovan_Guilfoyle · May 11, 2012, 5:07am

how difficult is it to solder the bumper buttons and the start and back buttons? also how do you do it?

gahrling · May 11, 2012, 1:44pm

Look at the pics in the first post, dude.

Bapex215 · May 11, 2012, 7:29pm

GameStop has this fight pad for 19.99 at the moment

RosserRooster · May 19, 2012, 2:10am

could some please tell me what number this resistor is I need to replace it thanks

Kuya_Joe · May 19, 2012, 9:11am

RX1 is 101
r8 is 105
haha what you do?

blklightning21 · May 19, 2012, 9:21am

wow these are 19.99 now. Are the PS3 versions wired or are they wireless?

jdm714 · May 19, 2012, 9:49am

Both Consoles are wired.

blklightning21 · May 19, 2012, 9:55am

Hot damn thanks buddy.

RosserRooster · May 19, 2012, 10:00am

Thanks joe I’m doing a dual vshg pcb mod and some of my tip cleaner dripped and as I’m cleaning it off the resistor when flying god knows where :xeye:

Jamin3131 · June 17, 2012, 9:32am

Where would I solder if I wanted to access to the Player LEDs?

jdm714 · June 17, 2012, 10:01am

Cathode to Cathode.
Anode to Anode.

rebelbrain · May 4, 2013, 6:24pm

Kuya_Joe:

Just for those that are curious and havent seen the new fightpad’s PCB yet here are pictures with the signal lines marked for easy modding.

Common Ground PCB like the other fightpads this new version is cut down considerably than the other three types we have seen in the past. Notice the turbo button has been moved as well as the LT,LB triggers. The USB connection is also moved from its previous spot on the other fightpads. Also the LS,DP,RS switch is moved more to the center on the other side of the pcb. DP is still in center so make sure that you pay attention to what that switch is placed before modding. Nice thing with the new board is like the brawlpad the pcb is labled. every contact pad has a marking telling the modder exactly what that contact pad is for. The signal points have changed a little on some of the contact pads so I have posted the proper solder points of each signal line for those using this pcb in a dual mod.

Notice that the directionals contact pad is similar to the guide contact pad… no more GIANT space to solder directionals but still more than enough to dot with solder for a good connection. The small spot above the xguide is also not there as before the older fightpads had that convinient spot to solder guide signal lines to. Still a lot of space for guide but watch your soldering…

Depending on what you use and where you want the pcb placed in a case there is still some dead space on the PCB that can be cut/dremeled off to make this fit.

ENJOY!

Frontside of PCB

http://img7.imageshack.us/img7/1572/sfxtpcb1.jpg

Backside of PCB

http://img808.imageshack.us/img808/4350/sfxtpcb2.jpg

Has anyone been able to find the pcb point for the Right stick , is it in the switch itself , It could be used !