PS3 dualshock 3 pin layout

FA-MAS · 2009-10-04T08:30:19.000Z

Here’s the layout from slagcoin’s site. Looks like the black #'s on ur drawing.

souji5 · 2009-10-04T19:57:29.000Z

FA-MAS:

Here’s the layout from slagcoin’s site. Looks like the black #'s on ur drawing.

http://www.slagcoin.com/joystick/pcb_diagrams/ps3_diagram3.jpg

The layout for this pad is a bit different, to the OP you may want to try dropping this in the padhacking thread to see if any the guys there would be able to help you out a bit more.

-I have one of these pads as well lying around and would be interested to know as well so it doesn’t go to waste lol

Gummo · 2009-10-05T04:59:15.000Z

I finished testing the board, and the pin numbering is like they way you have it in the black text. Even on top and odd on bottom. The pinout is the same as found on Slagcoin’s. I can’t tell you what the alt locations are for your board though, because theres at least 3 different versions of that type of board. The two I have have different looking alt locations. Funny though that they both of the pin number printed (unlike yours) and one of them have that black stuff (like yours) while the other one just has the copper pad already exposed.

BeWrong · 2012-03-27T05:47:33.000Z

i’m curious about this. I was looking for a solderless pad hack for the ps3 dual shock and this is what i found.

now to my stupid question… how do you split the ground with just 1 wire

jdm714 · 2012-03-27T05:52:54.000Z

Daisy-chain your Commons for the Joystick and Buttons.
http://slagcoin.com/joystick/pcb_wiring.html#SPLICING_AND_CHAINING

Daisy-chain.

Chapstick:

Can anyone explain daisy chaining pushbuttons to me? I just realized that I have no idea how to do it.

If it matters, I’m using a Madcatz 360 Gamestick (common ground). The JLF I’m using has a wire harness, so the DPad is taken care of, but as for my eight buttons, I don’t know how to daisy chain the grounds. Oh wise Internet, enlighten me!

I cannot explain by typing, so hopefully this picture I made will help you.
Took me like an hour to do this in MS Paint.
Laugh.

http://img4.imageshack.us/img4/9427/daisychain.png

Be careful what you are Daisy-chain.
Because you will NOT be doing Daisy-chain to Ground.

You will be Daisy-chain the respective Commons.
There will be three of four Commons you Daisy-chain.

Daisy-chain the red in diagram.
Daisy-chain the blue in diagram.
Daisy-chain the orange in diagram.

BeWrong · 2012-03-27T06:07:01.000Z

@jdm714 you’re always a big help!!! Thank you!

BeWrong · 2012-03-27T06:25:00.000Z

just wanted to make sure if i understand the distribution of the grounds before i open a dual shock 3.

feedback please

BeWrong · 2012-03-27T06:46:40.000Z

is the resistor really required for the whole thing to work?

can i use the the wires connected to the rumbles (the dual shocks) for an LED replacement?

jdm714 · 2012-03-27T06:51:01.000Z

just wanted to make sure if i understand the distribution of the grounds before i open a dual shock 3.
http://img.photobucket.com/albums/v139/pinaskpopclub/DS3PCB.jpg
feedback please

No.
It is Common, not Ground.

is the resistor really required for the whole thing to work?

can i use the the wires connected to the rumbles (the dual shocks) for an LED replacement?

Yes.

BeWrong · 2012-03-27T06:54:25.000Z

No.
It is Common, not Ground.

Yes.

Yes.

sorry for the term common i mean. but are the distributions correct on the colors that i made?

now i’m confused because of the resistors

jdm714 · 2012-03-27T06:59:57.000Z

Yes.

BeWrong · 2012-03-27T07:03:48.000Z

Yes.

thank you
last. can this be done without going through terminals? i know it’ll be messy but i just want to know.

thanks for explaining why the resistors are needed as well

jdm714 · 2012-03-27T07:27:28.000Z

Yes.

BeWrong · 2012-03-27T07:52:57.000Z

how was the black part on the pcb removed? was it just ripped off or was it soldered off? here’s what i’m pointing at:

jdm714 · 2012-03-27T08:00:23.000Z

It came like that.
Both come as how you see.
There is more than one style.

BeWrong · 2012-03-27T08:04:37.000Z

It came like that.
Both come as how you see.
There is more than one style.

i think mine’s the second one the one that has a black part. so is there anyway to solder through that or do i need to find an old dual shock 3 just like what he has?

jdm714 · 2012-03-27T08:05:45.000Z

What you have is the old one.

BeWrong · 2012-03-27T08:10:14.000Z

What you have is the old one.

i see. but is it possible to just solder the wires directly to the pins? or can it be taken off and i’ll see the same picture?

jdm714 · 2012-03-27T08:14:42.000Z

Shove wires for the non-cool way.
http://www.slagcoin.com/joystick/pcb_wiring.html#SOLDERLESS_EXTRACTED_PCBS

Buy AXISDapter for the cool way.
http://gdlk.co

Remove for the hard way.
You will not see the same thing.

BeWrong · 2012-03-27T08:18:12.000Z

Shove wires for the non-cool way.
http://www.slagcoin.com/joystick/pcb_wiring.html#SOLDERLESS_EXTRACTED_PCBS

Buy AXISDapter for the cool way.
http://gdlk.co

Remove for the hard way.
You will not see the same thing.

now i get it. so you just need to insert the wires without soldering them. i wasn’t able to get this when i read it at slagcoin.