Brook Universal Fighting Board Thread

[GOGO.Zippy]

If ultra SF2 can support wird fighting stick, I think Brook will study

@“GOGO.Zippy” Hori already announced a wired arcade stick for Switch

http://nintendoeverything.com/tons-of-hori-switch-accessories-leaked-zelda-tie-ins-fight-stick-more/nggallery/image/104490

@Dubon
Thanks your news.

[x64]

Unfortunately we don’t know if it’s wireless or wired yet

[Darksakul]

Really interested to see if they’ll be able to add Switch wired support. The HORI controllers didn’t even come out yet! I thought they did at launch.

The only wrinkle would be if Nintendo makes Hori ether make the stick wireless or add a security bluetooth module ala Sony and the PS4 controllers. The worst case scenario would be a new converter. Better than dropping $150 on a Switch-only stick.

They have what is definitely a wired hori pro controller. Rumor has it that it’s really cheap because there’s no wireless functionality.

That wired ps4 hori controller has a bluetooth module in it to verify its a licensed peripheral. If it didn’t have that it would time out every 8 minutes.

But thats the PS4, not the Switch.

[Dubon]

Unfortunately we don’t know if it’s wireless or wired yet

Actually we do, if look at the relevant slide it clearly sais “stick arcade filaire”

[x64]

Really interested to see if they’ll be able to add Switch wired support. The HORI controllers didn’t even come out yet! I thought they did at launch.

The only wrinkle would be if Nintendo makes Hori ether make the stick wireless or add a security bluetooth module ala Sony and the PS4 controllers. The worst case scenario would be a new converter. Better than dropping $150 on a Switch-only stick.

They have what is definitely a wired hori pro controller. Rumor has it that it’s really cheap because there’s no wireless functionality.

That wired ps4 hori controller has a bluetooth module in it to verify its a licensed peripheral. If it didn’t have that it would time out every 8 minutes.

But thats the PS4, not the Switch.

We don’t know the extent of Nintendo’s peripheral security yet. We likely won’t until brook gets their hands on Hori’s arcade stick.

Unfortunately we don’t know if it’s wireless or wired yet

Actually we do, if look at the relevant slide it clearly sais “stick arcade filaire”

Good eye!

[Brook_Engineer]

I have the intend to put a Brook Universal PC into my old Xbox 360 Madcatz TE S case, will 8 face buttons and 2 back buttons be enough?
So far i’d been using a PS2 Stick with the same amount of buttons in conjunction with the PS2>PS4 adapter but that one had an extra home button on
the adapter itself.

Is it possible to program a specific combination (such as Select+Start) to the Home button on the board or anything of that sort?
Adding another button hole would be near impossible for me and highly inconvenient.

or you may open up the cabinet if it comes to that

[hyperheavywing]

Okey, I got this pre-soldered version of UFB but I am still struggling to find out which goes where, I know what lever is but even on whole group set, there are more than 10 wires and I have 8 buttons, any advice which wires go where?

Brand New Breakout Board + 8 Cables + Brook Universal Fight Board Fighting |...

[Nobus3r1]

Hopefully this hasn’t been asked too many times but does PS and Touchpad (which registers as Select/Back on older consoles) work for firmware updates?

[Jasen_Hicks]

No, you need to use the actual SELECT button.

Jasen

[GOGO.Zippy]

Hopefully this hasn’t been asked too many times but does PS and Touchpad (which registers as Select/Back on older consoles) work for firmware updates?

@"Nobus3r1 ver. 2.0"
Touchpad keys already registers as SELECT / BACK. Please refer to look at this picture on Brook Website.

http://www.brookaccessory.com/detail/06960737/

[Jasen_Hicks]

@“GOGO.Zippy” - he was asking if he held TOUCHPAD and PS if that would get into boot loader mode so he could update the firmware. Unless you guys changed something, you still need a SELECT button to get into bootloader for updating firmware.

[Nobus3r1]

@“GOGO.Zippy” - he was asking if he held TOUCHPAD and PS if that would get into boot loader mode so he could update the firmware. Unless you guys changed something, you still need a SELECT button to get into bootloader for updating firmware.

Thanks. But yeah, this is what I was asking about. A button shortcut to emulate just tapping on the touchpad would also work as most PS4 fighting games use a touchpad tap to reset training mode.

[The_Real_Phoenix]

Hey guys just a small modification for the hitbox I’ve made for a friend.
I put a small slide switch on the pin 4 and 5 of J2 for enabling/disabling the SOCD. Mabe it can give you ideas:

http://i.imgur.com/vO65JZBm.jpg

First removing the pin and metalic part I don’t need:
http://i.imgur.com/MlkdSZzm.jpg

Then putting some Kapton tape on J2 holes I don’t want to touch:
http://i.imgur.com/7tGp210m.jpg

Soldering the switch:
http://i.imgur.com/rEda22Mm.jpg

In place in the hitbox:
http://i.imgur.com/ZdI15h4m.jpg

[Brook_Engineer]

Hey guys just a small modification for the hitbox I’ve made for a friend.
I put a small slide switch on the pin 4 and 5 of J2 for enabling/disabling the SOCD. Mabe it can give you ideas:

http://i.imgur.com/vO65JZBm.jpg

First removing the pin and metalic part I don’t need:
http://i.imgur.com/MlkdSZzm.jpg

Then putting some Kapton tape on J2 holes I don’t want to touch:
http://i.imgur.com/7tGp210m.jpg

Soldering the switch:
http://i.imgur.com/rEda22Mm.jpg

In place in the hitbox:
http://i.imgur.com/ZdI15h4m.jpg

goooooood job!

[DEZALB]

So this is missing a wire on the main harness side for the start button?

https://cdn2.bigcommerce.com/server500/d90a4/products/1349/images/9260/ist-top1__97711.1485654642.1280.1280.jpg?c=2

[platynumx]

So this is missing a wire on the main harness side for the start button?

Options is what start became on PS4. Share was formerly select.(going off dual shock layouts)

[GOGO.Zippy]

Hey guys just a small modification for the hitbox I’ve made for a friend.
I put a small slide switch on the pin 4 and 5 of J2 for enabling/disabling the SOCD. Mabe it can give you ideas:

http://i.imgur.com/vO65JZBm.jpg

First removing the pin and metalic part I don’t need:
http://i.imgur.com/MlkdSZzm.jpg

Then putting some Kapton tape on J2 holes I don’t want to touch:
http://i.imgur.com/7tGp210m.jpg

Soldering the switch:
http://i.imgur.com/rEda22Mm.jpg

In place in the hitbox:
http://i.imgur.com/ZdI15h4m.jpg

goooooood job!

@The_Real_Phoenix
It’s pretty good

[DEZALB]

So this is missing a wire on the main harness side for the start button?

Options is what start became on PS4. Share was formerly select.(going off dual shock layouts)

Cool, thanks for that

[BeMahMahMary]

Is there a Brook PCB that is Xbox 360 / Xbox One only (like the PS3/PS4 only PCB)?

[jopamo]

Nope. The aforementioned board includes native XInput anyway. You should be fine plugging it into a PC OR Xbox 360.