** Akishop.jp is now OPEN **

Hey, actually, on closer inspection, we found that one of the LS-32-01’s had two bent pins on the QD. Can we just bend it back and it’ll be fine?

dfoo, you can just bend it back. Seimitsu sticks are not that ruggedly built so it happens all the time unfortunately. Meh, that’s why I will always prefer Sanwa!

~Paik

per, any updates on the hori mice? or still out of stock?

!(?_?)!
If there where scans off it believe me you would hear about it :). Give it another day or two.

dfoo
This can happen in shipping, we always check it before we ship.

Som
We still have to preorder it so it will take a while. But you will get it no problem.

(I’m the guy asking about Sanwa IIDX buttons via email recently)

Sorry for asking so many questions about things, haha. I sent you a message with what I definitely want to order via your website. You can disregard my other messages sent before today. :slight_smile:

Thanks again!
–Brian

This may be a stupid question but with sanwa restrictors is there any difference if you put them on with the limiters at the top and bottom as opposed to left and right?

Neo,
can you guestimate the cost of shipping for:

Seimitsu LS-32-01
Sanwa OBSF-30 x6
Sanwa OBSM-30 x2
Seimitsu LB-39

to St. Paul, Mn. Airmail and EMS costs please…

Also, do you guys have the LS-32-02? I didn’t see it on the site or in the Siemitsu catolog.

The LS-32-02 is an LS-32-01. People call it an LS-32-02 because they see it printed on the PCB, but in actuality it is still an LS-32-01. It was most likely a revision of the original LS-32-01 PCB and thus they labeled it 02. The people who call it LS-32-02 just don’t know any better.

~Paik

Makes sense. I’m a dipshit. Scratch the last part of my message then.

Hahaha, nah, most people don’t know. I only personally know because Per and I talk parts like everyday… : ) I remember having asked him the same question months ago.

~Paik

Yeah. I won’t lie, I’m a stick noob. Hopefully, my HRAP modding goes better than my dumbass posts :wgrin:

Paik do you know the answer to my q?

I don’t even know what your question is asking. “limiters” is not a normal term. If you’re talking about the restrictor insert that can be turned, yes, there is a difference. The standard is diamond, if you turn it (45 degrees) you will have a diamond. The corners for a square are at the diagonal directions. The corners for the diamond are at up, down, left, and right. The latter is used for shmups (shooters).

~Paik

Dammit im so confused

Maybe i mean posts, theyre these 2 things that stick up on either side of the restrictor

It wont fit in a diamond shape cos the holes wont line up

It only fits in a square shape but in 2 different ways

There is no difference. What I am talking about is the square piece. Most people don’t know but the restrictor is 2 pieces of plastic, not just one. There is a smaller circular piece that sticks up near the center. You can turn that circular insert 45 degrees. Doing this will make the restrictor a diamond instead of a square. To turn the insert you have to push the insert towards the direction of the prongs and then turn it. If you turn one direction, it will go to the diamond, if you turn it the other direction, it will release the insert and it will come out completely and you will see this:
http://i10.photobucket.com/albums/a141/Paik4Life/Useful%20Photos/P1010149.jpg

*Note: This pic is not of Sanwa’s restrictor but a replica made by ASCII. IT is however exactly the same and even fits in Sanwa’s restrictor.

~Paik

Holy crap i never knew that :rofl:

I just did it with my square restrictor

Should be good for shooters :lol:

Hi,

I’ve been trying unsuccesfully for the past week to get a response to an order request by posting the form on the website. I’m looking for the following:

Seimitsu PS-14-P 320 - Pink x12
Sanwa OBSF-24 240 - Dark Blue x2 Purple x2
Seimitsu LB-39 205 - Pink x2
Sanwa GT-Y 550 - x2

Also, I’m interested in replacement bolts for Sanwa and Seimitsu panels. Finally, can you get ahold of a Power Supply replacement for a New Astro City, that utilizes the standard connectors fitted on the cab?

Im located in Colorado USA 80640.

Thanks and I hope to finally get a response,

Juan

CptMath
Sent reply, sorry for the wait.

juanjuan
Hi,

I sent you a PM. I got ALL your emails but could not reply :/. Price is in the PM.

Thanks for the PM.

I replied asking about the possibilityof getting a Power Supply for the New Astro.

Woohoo! Payment sent :slight_smile:

I know you are probably not used to ordering that stuff, so thanks for doing the “whole catalog”, as it were.