Seimitsu and sanwa buttons.
Differences in them?. I already tried sanwa buttons, theyāre sensitive asf and respond pretty good even when resting your fingers in them.
Though I want to try seimitsu, but, how sensitive are they? Do I need to push really hard so the input comes out? It responds the same way as the sanwa right? And also how much does it travels before reading the input?.
Im aware this isnāt the place to ask this, but I cannot seem to find an answer so, is it possible to buy an xbox 360 account with games here in the trading outlet? Or is it just not allowed?
Whatās up with you? Seriously are you still upset cause I shitted on your favorite game Nier?
If I left the original question there, you could complain that it was a stupid question.
I had problems figuring out putting some some pieces back together with a hori real arcade pro 4. You have a problem with me having a problem that you donāt know what the problem is but you feel entitled to the solution?. Get off my dick you dumb millennial.
Seimitsu is less sensitive than Sanwas. I tested this out long ago by stacking US nickles on top till the weight causes the plunger to go down.
Not the best scientific test, but the weight of a nickle is a known value and its results that can me reproduced.
I never talked to you about Nier. And I donāt care if you liked Nier or not.
This is the Question and Answer thread, the only stupid questions is the ones you donāt ask.
I do have a problem with people who ask a question, then edit their comment to erase that question and never give a solution.
As you rob anyone who have that same question a solution. This is a community were we help people, and not be selfish in their own actions.
If you canāt participate in the community and be civil you can leave. Also good job, you just burned one bridge. Try not to burn any others.
Yes you did talk to me about Nier. You must be salty from the Zelda thread for me sharing my opinions.
And what if the deletion was because I posted something in error or that was off topic or unrelated? My post did no harm to anyone and I left, itās you who felt the need for some reason to bring it upā¦and you have no idea what the original post or deletion was about. I am going to assume youāre trying to troll me at this point. Iāve been on this forum twice as long as you, you donāt need to tell me the rules.
Hey guys, I was wondering if you could help me out. I bought a used Mad Catz TE2 for PS4 and I canāt get it to fuunction on menu or in game. All the lights are lit up such as the toggle switch for directional use and the unlock button. Not sure if the small squares near the PS Home button are you supposed it light up.
I installed the required drivers on PC just to try and see if it works, and it does. Iām not sure what would cause it not to work on PS4, so Iām at a loss. Any help would be greatly appreciated.
Bought a Dragon; does it have the same actual metal balltop as the Obsidian? Otherwise, Iāll just steal the one off my Obsidian and replace that one with a chrome top. I need that metal feel for the Dragon.
Has anyone run into an issue dual modding a ufb, where the ufb wonāt recognize on ps3 or ps4 when ground and/or power is shared between both pcbs?
I have used both 20 pin headers and terminal posts, and swapped ground on other headers including touchpad and usb, and home button doesnāt activate.
It seems to recognize fine on the PC (except seperate issue where K3 is registering as z axis), since I dont need home on controller settings.
I will also be running an imp switch inbetween. Would it be possible to source power and ground for the second pcb from the switch rather than from the ufb?
Thatās odd and might suggest an issue more complicated than just a wire or two being lose (or disconnected). That said, it wouldnāt hurt to post a picture of the internals so that someone with an eye for such issues can take a look.
Hey guys, have a little problem with my hayabusa, thought i might ask here;
I recently opened up my hayabusa cus one of the switches was not registering well anymore.
(I was playing with kowal oversized and old Kowal octagonal restrictor plate and plasticdust was everywhere, cleaned it all up and stick/switch is working again, now with default actuator/gate)
After putting it back together and testing with a friends hayabusa aswell, there seems to be more resistance on the lever then normal, can clearly notice it next to my friends hayabusa.
So I read this might be due to overtightening the restirctor plate, took that all off and still the same feeling, took it apart again, re assembled, lubed with white silicone grease (generic), still the resistance remains.
Does anyone have any ideas? As far as I can see the thing only goes together one way so Iāve no idea whats wrong really.
thanks for any help!