if it requires .5v of power, how would one mod their stick to install this?
nominated! and like Zero said i just cant afford them right nowā¦ but as soon as we have a official release date i will most likely buy 2ā¦ or 3
Looks awesome, congrats and getting them production ready.
Are these the normal engage distance versions or are they sanwa flash sensitivity? crosses fingers for the later
Toodles
22
Thank you thank you thank you!
Frankly, I donāt know yet. I havenāt gotten the quote on the housings yet.
I have definitely considered it but havenāt looked too hard into doing so yet. NRX made a great design that would work perfect for just that purpose and already offered to let me use it for one, but I havenāt looked too hard into doing it yet. I can tell you that the costs that go with plastic molding are too high for me to want to get a mold and production run of washers made though; itād be a pretty big impact on the cost of the Spark. However, I think Iād like to chat with Art about getting a few custom engraved acrylic washers for at least the first X number of purchasers; maybe upload the file to Ponoko if folks wanted to make their own. Iām not sure yet, but it is on the table.
Is the description in the auction vague on this point?
+5 volts, not .5 volts. Check the description in the auction, but if youāre wanting a pictorial guide for your stick, youāre out of luck, especially since it depends on the stick.
The engage distances on them are actually a hair more sensitive than the flash. I doubt that in a double blind test anyone would be able to tell from using it though.
Awesome, good to see this moving forward. Shout outs to Toodles for holding it down and going hard.
People should not only look at how cool it will be to be the first to get one of these spark boards, but also at helping the community be able to get toodles to be able to get the production run started. So the high prices on the auction are worth it when you look at the big picture
looks likr these boards will sell up around $160 depending on how hard the bids go the last dayā¦ a lot of āfeelerā bids going through now. your smoking crack if you think its going to stay that low.
couple hours left! hype hype!
well a little more than a couple hours left but man I hope I winā¦Iām sure Iāll get all the bitches with one of these :wgrin: You know its going to be a hot min before these are mass produced word on the street is they put that old flash sanwa thing to shame the Sanwa flash is vanilla Flash and this is SUPER FLASH aka The Spark
Toodles
29
Attention all snipers, this is your 4 hour courtesy call. 
here comes the snipers!!! 50m and counting!
Toodles
32
One down, two to go, <2 minutes
Toodles
33
Congratulations to XMetal, ProtomanSTI, and Butteroj!
Thanks for all of the support guys. Since I know you all know me from here, please know that Iām dedicated to supporting your purchase and very much need your feedback. If you feel the need for adjustments to the sensitivity of the ones you receive, Iāll make sure it get setup to your liking.
XMetal
34
thanks so much toodles! i love opticals and i had to get my hands on one, but i think the community as a whole REALLY needed this. this way everyone can try an optical without having to search so much and pay a high premium. iām betting we get a lot of converts from switch to optical once you go in to mass production. youāve done a great service, toodles. thank you again
Woohoo!!! Merry xmas to me! Thanks again Marcus for all of your support for the community!
er actually
its me, paikman
not paik4life haha!
Thanks!
Toodles
37
Dāoh! My bad.
But thank you for correcting me. I needed to get ahold of you anyways }
strogg
38
Talk to your friendly neighborhood modder.
Know any in your area?
